[–] 2 points 1 month ago (5 children)

Milwaukee M12 Fuel, electronic wrench from like 10 to 250 ft lbs I think.

It’s just crazy expensive. You could get a half dozen hand torque wrenches for the same cost.

  • source
  • [–] 4 points 1 month ago

    I think the reason you can't find any such drill, is because it's just less efficient than cutting the material, and possibly have a much worse lifespan due to clogging of the drill and overheating.

    Grinding things will clog up the drill if the dust can't be pushed out of the hole. You're going to have a very hard time pushing the material/dust away with an abrasive tip, due to the nature of abrasives.

  • source
  • parent
  • context
  • I never went down this rabbit hole, but allegedly, "flint drills" existed since neolithic times and are simply a rotating stick (like a fire drill) with flint dust added for extra grit, as they are, allegedly, almost as hard as diamonds (and maybe extremely brittle? idk, but they sure seem like shitty diamonds)

    Can you get a stick into a drill and actually make a hole, like this? Maybe, but post the pictures.

  • source
  • [–] 2 points 1 month ago

    That's still a little vague. What are you actually trying to accomplish? What material, what size and orientation (perpendicular or angled) of hole, and what is the hole for?

    I'm looking for an answer like "I'm pre-drilling before toe-screwing 3/4" oak for the frame of a cabinet" or "I'm drilling out plug welds in 16 gauge sheet steel"

    For all we know, you're having an X/Y problem and the best advice might be to use a drill press or even some other tool entirely.

  • source
  • parent
  • context
  • [–] 7 points 1 month ago (4 children)

    The closest you can get to a general purpose drill bit is a basic twist drill made for metal. That works equally well on softer materials like wood and plastic. Other than that, no. You typically choose the bit based on what you're drilling into. Also, not all twist drills are made equal. HSS-R (rolled) works for wood, plastic and soft metals like aluminium, copper or brass. HSS-G (ground) is the bit you probably should be using especially if you're drilling into steel. Then there's also HSS-Co or HSS-E (cobalt) which is for hard metals like stainless steel. Then there's also carbide bits but those are for drill presses and such.

    Diamond bits work the way you describe but they're for ceramics and glass. If you try using one on wood or plastic it'll just clog up immediately. There's a reason twist drills look like that: they're designed to lift the removed material from the hole so that the bit can drill. A bit similar to how an orbital sander works much better with a vacuum attached so the dust layer doesn't sit between the sanding disc and the surface you're sanding.

    Then again, for concrete you not only need a masonry bit but ideally one with an SDS+ attachment for a dedicated hammer drill. You could technically use a diamond or non-hammer masonry bit as well but it would be extremely slow and you'd probably overheat the bit which affects the heat treatment of it which then causes it to get dull and quit drilling and just start heating up even more.

  • source
  • [–] 6 points 1 month ago

    Roll? As in moves before it bites into the material? Sounds like you need a center punch.

    As far as efficiency goes, I don't see how grinding off the material is more efficient than cutting it, which is what normal drill bits do. Or maybe slice? Shave?

  • source
  • parent
  • context
  • [–] [S] 1 point 1 month ago (3 children)

    cutting drill bit requires a slower revolving drill, so it doesn't roll on the surface, and also requires pressing harder. This can be slower and less efficient, than if the drill bit straightly grinds into the material.

  • source
  • parent
  • context
  • view more: ‹ prev next ›