I started with some knockoff clear shells and used this plus this for mister chef's but I think I used too much black. For barbieter, I used this and it was way more pink once done than I wanted. It probably could have used some black or blue added.

Both color sets were put in my heated ultrasonic cleaner at 50c for 20 minutes then removed, washed in cold water and allowed to dry. Heads up, the dye packets come with an intensifier, I used it on both but it has a weird chemical smell that lingers after you take and wash the parts. About a week on, they don't stink anymore.

The shells themselves were mid quality. The d-pads are super sloppy and the buttons stick so I used the original buttons from the first party shells. The gold shell I bought for the green accents needed the shoulder buttons and select button adjusted, it also came with 2 left triggers... Overall, I like how they came out. I wish the green was lighter but thats my fault. I may do some backlights or something in them to accent it but for now, its a unique setup and not sticky with 20 years of Doritos powder and baja blast.

It looks like they updated the article, I am disappointed but the screenshot lives on. Why can't we have anything nice anymore

Yes, its longer than the opening (because the post was not in line with the opening and I didn't want it to swing through the other way), yes, the post is not level, yes, I should probably not have used an existing fence post, no, I will not be fixing it. But look at the fit on the diagonal. MINT

That'll be four bucks baby! You want fries with that?

https://shop.8bitdo.com/products/8bitdo-64-classic-button-set

Look out little buddy, you look like a rock. I scooted him on his way back to the grass after getting his picture.

The ribeye was salted a day before and left on a wire rack in the fridge overnight, then smoked for about and hour at 225ish over mesquite and pulled when the internal temp hit about 110, then finished at 550ish. The bonus fillets at the front were because the family didn't think the 4lb Ribeye would be enough food, spoiler alert, I've been eating leftover steak all week.

Sister in law's grad party is today so I made 20lbs of faux-shawarama chicken kebabs.y little vision kamado grill wasn't gonna cut it so I fired up the camp chef ftg 600. They just barely fit.

Sister in law's grad party is today so I made 20lbs of faux-shawarama chicken kebabs.y little vision kamado grill wasn't gonna cut it so I fired up the camp chef ftg 600. They just barely fit.

It's been an ordeal but I'm (mostly) done with this. I tried using an iflash quad, a zif-cf-microsd adapter, and finally got this zif-msata adapter. The only one that worked is this setup. Worked is a loose term since this is supposed to be a 256gb ssd but its showing as 128gb... Anyways, the pictures below show the steps.

You need the firmware, software, and a 32 bit os to flash it. I'll add links later if I remember.

Remove the battery

Remove the 6 screws from the back

Not shown, remove the 4 silver screws from the sides, then the 2 from the compact flash card slot.

Separate the back from the case, there is a latch under the rubber flap, between the power jack and rca/usb port. I used a guitar pick to split it.

Remove the drive cover with the 4 small screws.

You should see the drive now, pull up on the black connector shell and pop the drive off. Then separate the zif cable by flipping the latch up and pull in the cable free. Keep the zif cable. I put a layer of kapton tape under the cable on the silver compact flash slot cover.

Put a layer of kapton tape on the mobo to keep the new drive adapter from doing any rubbing.

Attach the zif cable to the new drive adapter and install back in the connector. This positions your drive adapter where it needs to be.

Secure the drive adapter.

Here is the drive I used. Ymmv

Cover the back side of the ssd with kapton tape.

I used a little piece of foam to hold the rest of the stuff steady.

Reinstall the drive cover and assemble the rest of the unit. Boot to recovery mode by sliding the power switch over and holding it there while reconnecting the battery.

You need for select format drive and let it format, then you need to reload the firmware. To do that, you need the creative software. Ill upload that to a google drive or something. It requires a 32 bit os. I used an old netbook to do it.

As for why the capacity is wrong, I'm not sure. I could yank the drive out and find out, or I can leave it alone (option b is what I am doing)

I've been carrying a T-1000e around for a month or so and its been a lot of fun seeing all the new node notifications pop up. It feels good to know that there are more of y'all out there.

Name your nodes though! I love seeing all you dorks with a sense of humor.

Made from a garage door cable drum, garage door cable, brearing pillow blocks, 1" 0.120 wall tube, 9/16 shafting, and an amazon special awning roller. Its not sketchy at all, nope. Seriously though, don't stand under it.