cross-posted from: https://discuss.tchncs.de/post/66988984

What I have

I have an old Acer Aspire A515-51G and I also have a desire to have a home server. In combination this creates a need for the laptop to carry more HDDs than it can from factory. Usually it can take one M.2 SSD and one 2.5" SATA drive.

What I want

I want to make the laptop able to run at least 4 HDDs in RAID 5 for storage and have one SSD as boot drive.

What I did

The buying phase

• 4 HDDs
• M.2 to SATA adapter
• 12V/5V SATA power converter
• 12V 10A power supply

The designing phase

I needed space to hold the HDDs, so I designed a 3D printed a cage to attach to the bottom of my laptop. Two 80mm fans can be attach to it. You can see it on printables. Also I remixed a tray (here is the original) so the HDDs can slide in and out of the cage.

.

The assembly phase

A cutout at the bottom of the laptop was needed to give access to the SATA ports of the adapter.

I put a 2.5" SSD into the already present place for it in the laptop.

Then the cage was attached to the laptop, the HDDs were put in their trays, the trays inside the cage and the cables attached to the adapter and HDDs.

cross-posted from: https://discuss.tchncs.de/post/66988984

What I have

I have an old Acer Aspire A515-51G and I also have a desire to have a home server. In combination this creates a need for the laptop to carry more HDDs than it can from factory. Usually it can take one M.2 SSD and one 2.5" SATA drive.

What I want

I want to make the laptop able to run at least 4 HDDs in RAID 5 for storage and have one SSD as boot drive.

What I did

The buying phase

• 4 HDDs
• M.2 to SATA adapter
• 12V/5V SATA power converter
• 12V 10A power supply

The designing phase

I needed space to hold the HDDs, so I designed a 3D printed a cage to attach to the bottom of my laptop. Two 80mm fans can be attach to it. You can see it on printables. Also I remixed a tray (here is the original) so the HDDs can slide in and out of the cage.

.

The assembly phase

A cutout at the bottom of the laptop was needed to give access to the SATA ports of the adapter.

I put a 2.5" SSD into the already present place for it in the laptop.

Then the cage was attached to the laptop, the HDDs were put in their trays, the trays inside the cage and the cables attached to the adapter and HDDs.

cross-posted from: https://discuss.tchncs.de/post/66988984

What I have

I have an old Acer Aspire A515-51G and I also have a desire to have a home server. In combination this creates a need for the laptop to carry more HDDs than it can from factory. Usually it can take one M.2 SSD and one 2.5" SATA drive.

What I want

I want to make the laptop able to run at least 4 HDDs in RAID 5 for storage and have one SSD as boot drive.

What I did

The buying phase

• 4 HDDs
• M.2 to SATA adapter
• 12V/5V SATA power converter
• 12V 10A power supply

The designing phase

I needed space to hold the HDDs, so I designed a 3D printed a cage to attach to the bottom of my laptop. Two 80mm fans can be attach to it. You can see it on printables. Also I remixed a tray (here is the original) so the HDDs can slide in and out of the cage.

.

The assembly phase

A cutout at the bottom of the laptop was needed to give access to the SATA ports of the adapter.

I put a 2.5" SSD into the already present place for it in the laptop.

Then the cage was attached to the laptop, the HDDs were put in their trays, the trays inside the cage and the cables attached to the adapter and HDDs.

cross-posted from: https://discuss.tchncs.de/post/66988984

What I have

I have an old Acer Aspire A515-51G and I also have a desire to have a home server. In combination this creates a need for the laptop to carry more HDDs than it can from factory. Usually it can take one M.2 SSD and one 2.5" SATA drive.

What I want

I want to make the laptop able to run at least 4 HDDs in RAID 5 for storage and have one SSD as boot drive.

What I did

The buying phase

• 4 HDDs
• M.2 to SATA adapter
• 12V/5V SATA power converter
• 12V 10A power supply

The designing phase

I needed space to hold the HDDs, so I designed a 3D printed a cage to attach to the bottom of my laptop. Two 80mm fans can be attach to it. You can see it on printables. Also I remixed a tray (here is the original) so the HDDs can slide in and out of the cage.

.

The assembly phase

A cutout at the bottom of the laptop was needed to give access to the SATA ports of the adapter.

I put a 2.5" SSD into the already present place for it in the laptop.

Then the cage was attached to the laptop, the HDDs were put in their trays, the trays inside the cage and the cables attached to the adapter and HDDs.

cross-posted from: https://discuss.tchncs.de/post/66988984

What I have

I have an old Acer Aspire A515-51G and I also have a desire to have a home server. In combination this creates a need for the laptop to carry more HDDs than it can from factory. Usually it can take one M.2 SSD and one 2.5" SATA drive.

What I want

I want to make the laptop able to run at least 4 HDDs in RAID 5 for storage and have one SSD as boot drive.

What I did

The buying phase

• 4 HDDs
• M.2 to SATA adapter
• 12V/5V SATA power converter
• 12V 10A power supply

The designing phase

I needed space to hold the HDDs, so I designed a 3D printed a cage to attach to the bottom of my laptop. Two 80mm fans can be attach to it. You can see it on printables. Also I remixed a tray (here is the original) so the HDDs can slide in and out of the cage.

.

The assembly phase

A cutout at the bottom of the laptop was needed to give access to the SATA ports of the adapter.

I put a 2.5" SSD into the already present place for it in the laptop.

Then the cage was attached to the laptop, the HDDs were put in their trays, the trays inside the cage and the cables attached to the adapter and HDDs.

cross-posted from: https://discuss.tchncs.de/post/66988984

What I have

I have an old Acer Aspire A515-51G and I also have a desire to have a home server. In combination this creates a need for the laptop to carry more HDDs than it can from factory. Usually it can take one M.2 SSD and one 2.5" SATA drive.

What I want

I want to make the laptop able to run at least 4 HDDs in RAID 5 for storage and have one SSD as boot drive.

What I did

The buying phase

• 4 HDDs
• M.2 to SATA adapter
• 12V/5V SATA power converter
• 12V 10A power supply

The designing phase

I needed space to hold the HDDs, so I designed a 3D printed a cage to attach to the bottom of my laptop. Two 80mm fans can be attach to it. You can see it on printables. Also I remixed a tray (here is the original) so the HDDs can slide in and out of the cage.

.

The assembly phase

A cutout at the bottom of the laptop was needed to give access to the SATA ports of the adapter.

I put a 2.5" SSD into the already present place for it in the laptop.

Then the cage was attached to the laptop, the HDDs were put in their trays, the trays inside the cage and the cables attached to the adapter and HDDs.

What I have

I have an old Acer Aspire A515-51G and I also have a desire to have a home server. In combination this creates a need for the laptop to carry more HDDs than it can from factory. Usually it can take one M.2 SSD and one 2.5" SATA drive.

What I want

I want to make the laptop able to run at least 4 HDDs in RAID 5 for storage and have one SSD as boot drive.

What I did

The buying phase

• 4 HDDs
• M.2 to SATA adapter
• 12V/5V SATA power converter
• 12V 10A power supply

The designing phase

I needed space to hold the HDDs, so I designed a 3D printed a cage to attach to the bottom of my laptop. Two 80mm fans can be attach to it. You can see it on printables. Also I remixed a tray (here is the original) so the HDDs can slide in and out of the cage.

.

The assembly phase

A cutout at the bottom of the laptop was needed to give access to the SATA ports of the adapter.

I put a 2.5" SSD into the already present place for it in the laptop.

Then the cage was attached to the laptop, the HDDs were put in their trays, the trays inside the cage and the cables attached to the adapter and HDDs.

Her blog post: https://bitowl.online/about Link to the post in the screenshot: https://social.coop/@cwebber/116249815879392312

cross-posted from: https://discuss.tchncs.de/post/46277277

Recently Google decided that in the future for an app to be installable on an Android device, the developer of this app needs to be ID'd and registered at Google. They claim this is in order to "to better protect users". However, I think, this is a move to get more control over the Android ecosystem, and the data they can collect with it. If anyone who wants to develop an app for Android devices has to be registered with Google, this puts all the power of who to allow distributing an app to Google.

Furthermore F-Droid shows, that safe app stores can exist without registration, neither of users nor of developers. There is zero malware or spyware on the F-Droid store. What there is on F-Droid is thousands of beautiful, useful and, most importantly, safe apps. And this entire ecosystem is at risk, because Google wants to gain more control over its users and over the Android operating system.