A heatsink will be helpful if you have room for one. A giant heatsink with a fan and heat pipes is overkill though. Even enterprise SSDs don't go that far. They just have a plain aluminum heatsink that gets cooled by the case fans.
comments
Active ssd cooling is probably overkill but they can certainly throttle down to barely working speeds if they aren’t properly cooled. I could see there being scenarios where something like this is beneficial.
SSD waterblocks are also a thing
Thanks! Yeah, I'll leave it at that now and just enjoy that it works. I've recently been studying the very basics just out of curiosity, but when they started to talk about earth being a giant sink for electrons, they lost me (for now). I'll definitely pick it up again next month. 😊
I have no idea why ground goes into the negative node, but it was the only plausible configuration, since the power simply has to come from the positive node, according to conventional current
Electronics are complicated. Ground = negative node in most circuits. Unless you have studied electronics explicitly, most prior explanations you have heard are just good enough approximatons for whatever thing it was about.
Very interesring!
Done and in the process it even fixed the hardware clock.
Yeah, it’s just an inline resistor
A potentiometer is a resistor that you adjust using a dial. If you want control, you may want to get a PWM fan control module. There’s the Noctua NA-FC1 https://www.noctua.at/en/products/na-fc1 but that’s pretty much just a fancy expensive version, you can find the same concept for as little as $1-2 USD
I second this. If you can deal with those microconnections to an NTP server, search for how to enable NTP. On a systemd Linux system it should be a timedatectl option, I think.
Does the machine have internet access? If yes you should be able to have it set time from the internet automatically.
The pot is if you want to control the speed manually. The transistor if you want to control it from the pi (from the temperature for example).
If you want a potentiometer, there are two ways I think :
Have the potentiometer plugged to the pi ADC input, and in software regulate the pwm output to the transistor based on the signal coming from the pot.
Another way is to have the potentiometer in series with the fan and only control it from the pot. I've never built any circuit like this so there may be consideration to be put into the max current the pot can handle, but I guess for a small fan it could be okay.
In both cases you'll need a 12v source. Either a 12v power supply, or a DC step up from 5v (from the 5v power supply (maybe the same as the pi), not from a pin on the raspberry as it can't draw much current). In both cases, the grounds should be tied together so they all see the same voltage in reference to ground.
I can help you further if you want, but don't hesitate to ask a LLM for it as they can be quite good now for such circuits, and can in theory explain concepts you don't yet understand.
I just found a "noise reduction cable" from Noctua. It ads 51 Ohms. I have no idea how to calculate what the new voltage would be on a 12V 2A DC power supply ( https://www.noctua.at/en/products/nv-ps1/specifications ), but Noctua's website says that the cable lowers fan speeds, so I'll give it a try.
Assuming the supply can saturate the current the fan will use, at 12V it’ll be running at full speed. That’s probably pretty loud. Give it 5V, it’ll run slower and quieter.
That would obviously work with older dc fans but modern ones use pwm which iirc is a constant voltage just pulsed to varying degrees (thus pulse width modulation)
You should indeed power it with 12v
I guess I have to try. It either stalls and doesn't turn at all, or I get a comfortable breeze.
Bookmarked!
Thanks! That lead me to discover this: https://www.noctua.at/en/products/nv-ps1/specifications Which I guess would have the fan blast away at full speed, but maybe I could force a potentiometer in between somewhere somehow...?
Or, I just go the easy way, as you said. I just hate to know that the Wraith is sitting in my closet, unused... XD
does it work at all on 5v?
Right! I have no reason for it to run art full speed on a Pi anyway. I'm leaning towards buying a 5V USB adapter.
5V seems to the consensus, so I'll go in that direction. But I do want to keep the chassi on, so I think I'll go with a 5V USB.
I had no idea the Pi's output could be boosted. Sweet!
Right, so less voltage, less speed. Couldn't I "shove" a potentiometer in between and give it around 7,5V or whatever gives the best noise to temp results?
Gotcha! Thanks for the directions! Any reason why I shouldn't power it with 12V, since it says 12 on the fan...?
Thanks, I thought of that too, and I'll go with that if this doesn't work. I just didn't want this little Wraith lying around unused and the size fits so well on the Pi 😄