▲ 1 ▼ As you can see, I am using ALL the I/O the RP2350B has to offer (studio8502.files.fedi.monster) submitted 1 day ago by mos_8502@studio8502.ca to c/microblogs@piefed.social 9 comments fedilink hide all child comments As you can see, I am using ALL the I/O the RP2350B has to offer.
[–] mos_8502@studio8502.ca [S] 1 point 1 day ago (8 children) The routing is not my best work ever, but it should do the trick. permalink fedilink source hideshow 8 child comments replies: [–] mos_8502@studio8502.ca [S] 1 point 1 day ago (7 children) If the userport routing looks like an afterthought, that's because it was. It was suggested, and it used up the last I/O on the board, and if I do a respin at some point it'll be tidier. I wasn't ripping up four days' work for ten GPIO pins that might never be used. permalink fedilink source parent hideshow 7 child comments replies: [–] mos_8502@studio8502.ca [S] 1 point 1 day ago (6 children) The 1.1V power supply and the crystal schematics were literally copied and pasted from the official example schematics. So I'm pretty sure it's right. permalink fedilink source parent hideshow 6 child comments replies: [–] mos_8502@studio8502.ca [S] 1 point 1 day ago (5 children) Got your PSRAM and SPI flash ROM right here. The firmware has to boot the RP2350B and contain the bitstream for the FPGA, which gets loaded via bit-banging SPI on its own four pins. permalink fedilink source parent hideshow 5 child comments replies: [–] mos_8502@studio8502.ca [S] 1 point 1 day ago (4 children) Stupid simple power supply: USB-C +5V, 15W. Way more than anything on this board needs anyway. Little 3.3V regulator for the I/O, 1.2V for the FPGA.I could have run the 1.2V over to the MCU to replace the fiddly switching power supply, but I worry that doing that will hamper overclocking. permalink fedilink source parent hideshow 4 child comments replies: [–] mos_8502@studio8502.ca [S] 1 point 1 day ago (3 children) VERA outputs VGA via a simple resistor DAC. Nothing special here. permalink fedilink source parent hideshow 3 child comments replies: [–] mos_8502@studio8502.ca [S] 1 point 1 day ago (2 children) A DAC for the I2S audio from VERA outputs line-level stereo. This part I know works. It's lifted from Sentinel 65X. permalink fedilink source parent hideshow 2 child comments replies: [–] mos_8502@studio8502.ca [S] 1 point 1 day ago (1 child) User port and debug serial port, plus the two SNES controller ports (not shown) round out the system.Not much to it really. The magic is all in the firmware. permalink fedilink source parent hideshow 1 child comment replies: [–] mos_8502@studio8502.ca [S] 1 point 1 day ago Hopefully the result provides people with some joy. It's as cheap and feature packed as I can make it. If I could cram in another feature or scrape a dollar off the price tag, I would. permalink fedilink source parent
[–] mos_8502@studio8502.ca [S] 1 point 1 day ago (7 children) If the userport routing looks like an afterthought, that's because it was. It was suggested, and it used up the last I/O on the board, and if I do a respin at some point it'll be tidier. I wasn't ripping up four days' work for ten GPIO pins that might never be used. permalink fedilink source parent hideshow 7 child comments replies: [–] mos_8502@studio8502.ca [S] 1 point 1 day ago (6 children) The 1.1V power supply and the crystal schematics were literally copied and pasted from the official example schematics. So I'm pretty sure it's right. permalink fedilink source parent hideshow 6 child comments replies: [–] mos_8502@studio8502.ca [S] 1 point 1 day ago (5 children) Got your PSRAM and SPI flash ROM right here. The firmware has to boot the RP2350B and contain the bitstream for the FPGA, which gets loaded via bit-banging SPI on its own four pins. permalink fedilink source parent hideshow 5 child comments replies: [–] mos_8502@studio8502.ca [S] 1 point 1 day ago (4 children) Stupid simple power supply: USB-C +5V, 15W. Way more than anything on this board needs anyway. Little 3.3V regulator for the I/O, 1.2V for the FPGA.I could have run the 1.2V over to the MCU to replace the fiddly switching power supply, but I worry that doing that will hamper overclocking. permalink fedilink source parent hideshow 4 child comments replies: [–] mos_8502@studio8502.ca [S] 1 point 1 day ago (3 children) VERA outputs VGA via a simple resistor DAC. Nothing special here. permalink fedilink source parent hideshow 3 child comments replies: [–] mos_8502@studio8502.ca [S] 1 point 1 day ago (2 children) A DAC for the I2S audio from VERA outputs line-level stereo. This part I know works. It's lifted from Sentinel 65X. permalink fedilink source parent hideshow 2 child comments replies: [–] mos_8502@studio8502.ca [S] 1 point 1 day ago (1 child) User port and debug serial port, plus the two SNES controller ports (not shown) round out the system.Not much to it really. The magic is all in the firmware. permalink fedilink source parent hideshow 1 child comment replies: [–] mos_8502@studio8502.ca [S] 1 point 1 day ago Hopefully the result provides people with some joy. It's as cheap and feature packed as I can make it. If I could cram in another feature or scrape a dollar off the price tag, I would. permalink fedilink source parent
[–] mos_8502@studio8502.ca [S] 1 point 1 day ago (6 children) The 1.1V power supply and the crystal schematics were literally copied and pasted from the official example schematics. So I'm pretty sure it's right. permalink fedilink source parent hideshow 6 child comments replies: [–] mos_8502@studio8502.ca [S] 1 point 1 day ago (5 children) Got your PSRAM and SPI flash ROM right here. The firmware has to boot the RP2350B and contain the bitstream for the FPGA, which gets loaded via bit-banging SPI on its own four pins. permalink fedilink source parent hideshow 5 child comments replies: [–] mos_8502@studio8502.ca [S] 1 point 1 day ago (4 children) Stupid simple power supply: USB-C +5V, 15W. Way more than anything on this board needs anyway. Little 3.3V regulator for the I/O, 1.2V for the FPGA.I could have run the 1.2V over to the MCU to replace the fiddly switching power supply, but I worry that doing that will hamper overclocking. permalink fedilink source parent hideshow 4 child comments replies: [–] mos_8502@studio8502.ca [S] 1 point 1 day ago (3 children) VERA outputs VGA via a simple resistor DAC. Nothing special here. permalink fedilink source parent hideshow 3 child comments replies: [–] mos_8502@studio8502.ca [S] 1 point 1 day ago (2 children) A DAC for the I2S audio from VERA outputs line-level stereo. This part I know works. It's lifted from Sentinel 65X. permalink fedilink source parent hideshow 2 child comments replies: [–] mos_8502@studio8502.ca [S] 1 point 1 day ago (1 child) User port and debug serial port, plus the two SNES controller ports (not shown) round out the system.Not much to it really. The magic is all in the firmware. permalink fedilink source parent hideshow 1 child comment replies: [–] mos_8502@studio8502.ca [S] 1 point 1 day ago Hopefully the result provides people with some joy. It's as cheap and feature packed as I can make it. If I could cram in another feature or scrape a dollar off the price tag, I would. permalink fedilink source parent
[–] mos_8502@studio8502.ca [S] 1 point 1 day ago (5 children) Got your PSRAM and SPI flash ROM right here. The firmware has to boot the RP2350B and contain the bitstream for the FPGA, which gets loaded via bit-banging SPI on its own four pins. permalink fedilink source parent hideshow 5 child comments replies: [–] mos_8502@studio8502.ca [S] 1 point 1 day ago (4 children) Stupid simple power supply: USB-C +5V, 15W. Way more than anything on this board needs anyway. Little 3.3V regulator for the I/O, 1.2V for the FPGA.I could have run the 1.2V over to the MCU to replace the fiddly switching power supply, but I worry that doing that will hamper overclocking. permalink fedilink source parent hideshow 4 child comments replies: [–] mos_8502@studio8502.ca [S] 1 point 1 day ago (3 children) VERA outputs VGA via a simple resistor DAC. Nothing special here. permalink fedilink source parent hideshow 3 child comments replies: [–] mos_8502@studio8502.ca [S] 1 point 1 day ago (2 children) A DAC for the I2S audio from VERA outputs line-level stereo. This part I know works. It's lifted from Sentinel 65X. permalink fedilink source parent hideshow 2 child comments replies: [–] mos_8502@studio8502.ca [S] 1 point 1 day ago (1 child) User port and debug serial port, plus the two SNES controller ports (not shown) round out the system.Not much to it really. The magic is all in the firmware. permalink fedilink source parent hideshow 1 child comment replies: [–] mos_8502@studio8502.ca [S] 1 point 1 day ago Hopefully the result provides people with some joy. It's as cheap and feature packed as I can make it. If I could cram in another feature or scrape a dollar off the price tag, I would. permalink fedilink source parent
[–] mos_8502@studio8502.ca [S] 1 point 1 day ago (4 children) Stupid simple power supply: USB-C +5V, 15W. Way more than anything on this board needs anyway. Little 3.3V regulator for the I/O, 1.2V for the FPGA.I could have run the 1.2V over to the MCU to replace the fiddly switching power supply, but I worry that doing that will hamper overclocking. permalink fedilink source parent hideshow 4 child comments replies: [–] mos_8502@studio8502.ca [S] 1 point 1 day ago (3 children) VERA outputs VGA via a simple resistor DAC. Nothing special here. permalink fedilink source parent hideshow 3 child comments replies: [–] mos_8502@studio8502.ca [S] 1 point 1 day ago (2 children) A DAC for the I2S audio from VERA outputs line-level stereo. This part I know works. It's lifted from Sentinel 65X. permalink fedilink source parent hideshow 2 child comments replies: [–] mos_8502@studio8502.ca [S] 1 point 1 day ago (1 child) User port and debug serial port, plus the two SNES controller ports (not shown) round out the system.Not much to it really. The magic is all in the firmware. permalink fedilink source parent hideshow 1 child comment replies: [–] mos_8502@studio8502.ca [S] 1 point 1 day ago Hopefully the result provides people with some joy. It's as cheap and feature packed as I can make it. If I could cram in another feature or scrape a dollar off the price tag, I would. permalink fedilink source parent
[–] mos_8502@studio8502.ca [S] 1 point 1 day ago (3 children) VERA outputs VGA via a simple resistor DAC. Nothing special here. permalink fedilink source parent hideshow 3 child comments replies: [–] mos_8502@studio8502.ca [S] 1 point 1 day ago (2 children) A DAC for the I2S audio from VERA outputs line-level stereo. This part I know works. It's lifted from Sentinel 65X. permalink fedilink source parent hideshow 2 child comments replies: [–] mos_8502@studio8502.ca [S] 1 point 1 day ago (1 child) User port and debug serial port, plus the two SNES controller ports (not shown) round out the system.Not much to it really. The magic is all in the firmware. permalink fedilink source parent hideshow 1 child comment replies: [–] mos_8502@studio8502.ca [S] 1 point 1 day ago Hopefully the result provides people with some joy. It's as cheap and feature packed as I can make it. If I could cram in another feature or scrape a dollar off the price tag, I would. permalink fedilink source parent
[–] mos_8502@studio8502.ca [S] 1 point 1 day ago (2 children) A DAC for the I2S audio from VERA outputs line-level stereo. This part I know works. It's lifted from Sentinel 65X. permalink fedilink source parent hideshow 2 child comments replies: [–] mos_8502@studio8502.ca [S] 1 point 1 day ago (1 child) User port and debug serial port, plus the two SNES controller ports (not shown) round out the system.Not much to it really. The magic is all in the firmware. permalink fedilink source parent hideshow 1 child comment replies: [–] mos_8502@studio8502.ca [S] 1 point 1 day ago Hopefully the result provides people with some joy. It's as cheap and feature packed as I can make it. If I could cram in another feature or scrape a dollar off the price tag, I would. permalink fedilink source parent
[–] mos_8502@studio8502.ca [S] 1 point 1 day ago (1 child) User port and debug serial port, plus the two SNES controller ports (not shown) round out the system.Not much to it really. The magic is all in the firmware. permalink fedilink source parent hideshow 1 child comment replies: [–] mos_8502@studio8502.ca [S] 1 point 1 day ago Hopefully the result provides people with some joy. It's as cheap and feature packed as I can make it. If I could cram in another feature or scrape a dollar off the price tag, I would. permalink fedilink source parent
[–] mos_8502@studio8502.ca [S] 1 point 1 day ago Hopefully the result provides people with some joy. It's as cheap and feature packed as I can make it. If I could cram in another feature or scrape a dollar off the price tag, I would. permalink fedilink source parent
all 9 comments