191
A brick has been shat (lemmy.ca)
submitted 1 month ago by to c/pcmasterrace@lemmy.world
65 comments fedilink hide all child comments
 

As an atheist, I ask for prayers that the backup's good.

E: Your solidarity has worked. The backup is good and not too old. Note for myself and you - install your OS on a snapshotting filesystem so that live backups are possible.

you are viewing a single comment's thread
view the rest of the comments
[–] [S] 23 points 1 month ago (15 children)

Because on the latest ASRock boards it's damn near impossible to remove their metal heatsink bullshit for installing M2 drives. It's easier to strip naked the drive and use their bullshit. Except when it isn't. 🥹

  • permalink
  • fedilink
  • source
  • parent
  • hideshow 15 child comments
    •
  • [–] 3 points 1 month ago (2 children)

    So the heatsink is not needed? Or did you plan on putting it back afterwards??

    I'm so confused.

  • permalink
  • fedilink
  • source
  • parent
  • hideshow 2 child comments
    •
  • [–] [S] 4 points 1 month ago

    The motherboard has big, built-in heatsinks on its M2 slots. You install a naked NVMe drive in the M2 slots and the motherboard heatsinks (with thermal pads) hug it from both sides.

  • permalink
  • fedilink
  • source
  • parent
  • [+] -8 points 1 month ago (10 children)

    So you're a better engineer than whoever designed that metal heat sink "bullshit".?

    Why would you do this? It makes no sense. Hope you learned something.

  • permalink
  • fedilink
  • source
  • parent
  • hideshow 10 child comments
    •
  • [–] 7 points 1 month ago (4 children)

    Lmao these kinds of comments always crack me up. You speak with confidence from a position of ignorance with a sprinkling of “the engineers know best”.

  • permalink
  • fedilink
  • source
  • parent
  • hideshow 4 child comments
    •
  • [+] -6 points 1 month ago (3 children)

    Odd, I do detect someone speaking with confidence from a position of abject cretinitude.

    Can you guess who it is?

  • permalink
  • fedilink
  • source
  • parent
  • hideshow 3 child comments
    •
  • [–] 5 points 1 month ago

    Two things, an ssd and a motherboard, both with heat sinks built in. You can’t use both heat sinks. One of them has to be removed, and OP chose the wrong one based on the incorrect assumption that the heatsink on the ssd was not held on with such a strong adhesive.

    You come in here with essentially “lmao you’re an idiot why would you remove the heatsink? The engineers know what they are doing why would you know better?”

    So if they should remove neither of the heat sinks, since an engineer put them both where they are, they should just throw out the drive?

  • permalink
  • fedilink
  • source
  • parent
  • [–] 6 points 1 month ago (1 child)

    Re-read their comment. They had to remove THIS heatsink because the ASRock mobo made it too difficult to remove the mobo side heatsink, which is meant to go over naked drives

  • permalink
  • fedilink
  • source
  • parent
  • hideshow 1 child comment
    •
  • [+] -8 points 1 month ago

    Then either buy the right motherboard or the right drive. Peeling things off at random and then lashing out at the engineering is some kind of tistic temper tantrum for the emotionally disregulated.

    Seek therapy.

  • permalink
  • fedilink
  • source
  • parent
  • [–] [S] 2 points 1 month ago* (last edited 1 month ago) (2 children)

    Not the heatsink in the picture. The motherboard's M2 heatsinks:

    Especially the bottom one. It leaves no space for installing an NVMe with a stock heatsink. To remove it, it requires access to the rear of the board, which now has this big ass metal backplate covering it. So one has to remove the whole backplate to access the screws holding the bottom M2 heatsinks. Only then they can be removed and a factory-heatsinked SSD installed. I thought that would've been more work, and I didn't want to modify a board I have not tested yet that could need to be RMAd if defective.

    The lessons for me are:

    • Always keep a recent system backup
    • Don't remove stock NVMe heatsinks I did not install myself - they could be glued
    • If stuck with such SSDs, mod the motherboard after testing it
  • permalink
  • fedilink
  • source
  • parent
  • hideshow 2 child comments
    •
  • [–] -5 points 1 month ago (1 child)

    Dear dummy, please select your item carefully BEFORE purchasing it.

    Duh. Exhausting dealing with people like you.

  • permalink
  • fedilink
  • source
  • parent
  • hideshow 1 child comment
    •
  • [–] [S] 6 points 1 month ago* (last edited 1 month ago)

    LMAO, this SSD was purchased many years ago and was in active use. The previous ASRock board it was used in had the same toolless M2 mechanism but did not have a backplate which made the bottom heatsink easily removable, which I had done and this exact SSD was installed in it. The new board's product page doesn't say anything about a backplate blocking M2 heatsink removal, or a backplate at all. Given the information available I bought the right product.

    Now kindly fuck off.

  • permalink
  • fedilink
  • source
  • parent