105
What is this called? (media.piefed.social)
submitted 5 months ago by to c/woodworking@lemmy.ca
locked 47 comments fedilink hide all child comments
 
What is this called?
you are viewing a single comment's thread
view the rest of the comments
[–] 9 points 5 months ago (12 children)

So if I'm understanding it correctly, someone would drill a hole in the wood, line up the spiky bit, and then hammer it in. Going by the comments, it sounds like these things fall out a lot. What is the recommended alternative?

  • permalink
  • fedilink
  • source
  • parent
  • hideshow 12 child comments
    •
  • [–] 15 points 5 months ago (8 children)

    It's not that bad, when used correctly they stay put a long time.

    When I design furniture that needs one, I usually design it so the t-nut goes in from the other side so the screw secures it in, but honestly unless the wood gets wet, the t-nut will hold fine.

    There are similar t-nuts with tiny screws instead of hammer in options. You can chisel out the wood and epoxy in a hex nut. You can just screw the leveling foot directly into the wood. You can put a larger metal plate in place.

    But if the wood fails and the t-nut falls out, you can also just repair the wood or epoxy it back in and it'll hold for another few decades.

    Most wood furniture won't last forever without repairs anyway, the fixes over the years are part of the charm.

  • permalink
  • fedilink
  • source
  • parent
  • hideshow 8 child comments
    •
  • [–] 2 points 5 months ago (2 children)

    Aren’t these used for adjustability? Meaning you can loosen or tighten them to deal with unevenness?

    And if that’s the case, wouldn’t reversing the t nut result in the weight of the furniture pushing the t nut out of place?

  • permalink
  • fedilink
  • source
  • parent
  • hideshow 2 child comments
    •
  • [–] 4 points 5 months ago (1 child)

    You can use t-nuts for a lot of reasons. A t-nut specifically is for screwing machine screws into wood. This particular use case is using that machine screw as a leveler, but it's not the only case.

    Sometimes you just want a large, solid bolt to hold things together, but allow them to be taken apart. In those cases I try to put the t-nut the other way around so assembly tightens the nut.

  • permalink
  • fedilink
  • source
  • parent
  • hideshow 1 child comment
    •
  • [–] 1 point 5 months ago (4 children)

    When I design furniture that needs one, I usually design it so the t-nut goes in from the other side so the screw secures it in,

    I'm confused - it seems like thats what would happen here? The foot would push the T nut into the wood from below?

  • permalink
  • fedilink
  • source
  • parent
  • hideshow 4 child comments
    •
  • [–] 1 point 5 months ago (3 children)

    Think about what would happen if you just pulled on the foot. The T-nut would come right out.

    Compare that to how you would typically use a normal nut and bolt to secure two pieces of material, with the bolt head and nut on opposite sides of the material being secured.

  • permalink
  • fedilink
  • source
  • parent
  • hideshow 3 child comments
    •
  • [–] 2 points 5 months ago (2 children)

    Sure, but wouldnt the normal pressure of the floor pressing into the foot then immediately pop the t nut out of the top of the wood you nailed it into?

  • permalink
  • fedilink
  • source
  • parent
  • hideshow 2 child comments
    •
  • [–] 1 point 5 months ago (1 child)

    Well yeah, but you wouldn't use it that way for an adjustable foot -- that's a weird special case where the bolt is in compression. Normally the bolt is in tension, and that's when you'd want the T-nut on the opposite side of the wood.

  • permalink
  • fedilink
  • source
  • parent
  • hideshow 1 child comment
    •
  • [–] 5 points 5 months ago

    It depends what you use them for. If you arange them so the force on the bolt is driving the spikes into the wood, they are very strong, and a handy way to anchor a bolt into wood in a removable way. Where they're not so good is when the force isn't directly along that line. Sideways force tends to loosen them and then they fall off, and force in the opposite direction obviously pushes them out.

  • permalink
  • fedilink
  • source
  • parent
  • [–] 3 points 5 months ago*

    What is the recommended alternative?

    There are other styles of threaded inserts for wood.

    I used some of the first type to make leg extensions for an IKEA coffee table to turn it into a waist-height table. They were picked mostly to match what the piece already used rather than because I thought they were better than the T-nut style ones, but they worked fine.

  • permalink
  • fedilink
  • source
  • parent