previous post

TL; DR: There was the loud static noise coming from my Yaesu FT-2900R rig at full volume when I put it on standby, lasting until I either turn it back on or fully cut the power. To fix it, I replaced a JFET that drives the power MOSFET.

Seems there's some interest gathered around this, so I figured I'd give an update.

I'd like to give credit to Yaesu's impeccable documentation. Its circuit diagrams as well as the component maps and list provided me with all the information I needed to gain a complete understanding of this device. I did had to look what some of the components do, but it's all available out there.

I've came to appreciate the simplicity of the design. Save for the microcontroller and an EEPROM, it's all analog.

Anyway, without further ado...

Analysis

I seem to have misunderstood some things about the power management. Seems that during the standby mode, everything but the microcontroller gets turned-off. I was right that the microcontroller would enter the low-power mode.

The 13.8v DC main power goes thru only three different paths:

  • the final amp, as its bias, probably connected directly due to the sheer amount of current it needs in its full capacity
  • the microcontroller and its supporting components, regulated into 5v
  • the power MOSFET, which acts as the main gatekeeper to the rest of the system (audio, VCO, signal processing)

Hence, what signal goes where is completely irrelevant in this state, since they're all supposed to be off, including the shift register I suspected to be the cause of trouble.

One piece that was key was that the power MOSFET is driven by a JFET (DTC144EE, a p-channel, marked Q1014), which is driven by the microcontroller in a signal line called REG SW (probably means "regulator switch"). The MOSFET's gate is pulled up to the 13.8v by a 100k ohm.

Observation

Contrary to the expected condition, the power MOSFET kept on delivering power even in standby mode. Furthermore, reading the voltage of its gate yielded 5.9v, which contradicted the supposed 0v in the circuit diagram. What's even weirder was that the voltage at the gate became higher during standby, at 6.4v.

Since the signal comes from the microcontroller itself, I checked the voltage thru-out the path, where I found that the voltage in the entire signal line was the same as the gate, even up to right at the microcontroller pin. This is especially strange, since the signal level is supposed to be 5v at most.

For good measure, I checked that the resistor values are correct.

Last but not least, I checked for continuity between the MOSFET gate and the REG SW line, and they're indeed connected directly.

Interpretation

My hypothesis was that the weird value on the REG SW signal line was a combination between the current coming from the microcontroller pin and the main DC power.

With the fact that the MOSFET gate and the REG SW line was connected, and that the resistor values were correct, pointed me to the driver JFET.

Solution

I cannibalize a spare DTC144EE JFET from a scrap. After unsoldering the old problematic one from my rig, I soldered in the good one.

After cleaning up, I connected the power to my rig and put it on standby. To my surprise, the power MOSFET output 0v. For good measure, I made sure the rig was able to do all its normal function (it did).

I then put the rig back on standby, and left it overnight. So far there's no static noise coming out of it at all.

I guess my fix really works! Perhaps the shady seller put in a wrong component or something.

Continuity

This is definitely not the end of the journey. In fact, it may have only just begun.

One question remain on how the clock signal gets generated, since the microcontroller doesn't seem to be the one doing the generating after all. I don't really feel the urgency to really loom for an answer, tho. I'm just glad I was able to get my rig to work!

Anywho, thanks for reading so far. There was actually a whole list of fixes I did to this thing if you care to know more about it.

 

previous post

Posting it here for posterity, and for the possibility of somebody passing-by having some idea.

I've confirmed that it wasn't an issue with power supply. The static noise itself comes from the RF noise in the air, but that's beside the point, as the radio is supposed to remain silent.

Analysis

With the help of the radio rig's technical supplement, as well as the datasheets for the involved components, I was able to get the grasp for the radio's circuit logic.

In short:

  • captured signal gets passed thru the mute gate to the volume control circuit
  • the volume control circuit passes it to the audio output

What happens in between:

  • the volume control circuit depends on the virtual ground set by a CD4094B shift register, marked Q1048, thru a 5 volt signal
  • the same shift register also controls the mute gate, also thru a 5 volt signal
  • the shift register in question is controlled by the microcontroller (processor of H8S/2268 series) thru clock signal and serial data, which seems to be shared with other components, notably an ADC.

It is noted in the block diagram that the clock signal comes from the microcontroller. The circuit diagram shows it would be the pin 74 of the microcontroller. However, the documentation for the microcontroller, the pin in question is for clock input. There are also pins for the clock output, but not for that pin.

It worth also to note that the H8S microcontroller can have powered-down states. There are multiple different types available, but the only one that applies here would be the software type. Under this state, an interrupt signal can be used to 'wake up' the processor back into the normal on mode. In the case of this rig, the power button serves both as a GPIO input to activate the powered down mode in normal mode, and as an interrupt source to wake up the processor in the powered down mode.

Observation

In the normal on state, the shift register marked Q1048 output 5v for both the signal going to the audio control circuit's virtual gound as well as the one going to the mute gate.

In the standby state, at first this condition persists. After a while, tho, when the loud static appear, the shift register seems to be disabled as both the signals I observed above both become 0v.

Also when the loud static appears, shorting the microcontroller's RESET pin to the Vcc seems to get rid of it.

Interpretation

When the radio rig get 'turned off' to standby mode, most of the radio circuitry seems to still be active. Furthermore, the only thing that are disabled completely are the screen and the input buttons, except for the power button.

I am still investigating the behavior of the microcontroller, the mute gate, as well as the volume control within this state.

So far what I'm seeing is that the clock signal runs normally until it doesn't, and that is what allows the audio signal to pass with maximum volume.

It is also possible that the signal is supposed to be stopped by the mute gate even before it gets to the audio volume control. This is the avenue I'm currently exploring.

Let me know if you have any thoughts!

 

It's me again, back with my Yaesu FT-2900R rig. I've worked thru most of the issues with it, but some remain.

One of the most annoying ones would be the intermittent loud static noise (as if I'd turn the radio on, turn up the volume, and disable the squelch) that randomly appears when I leave my radio off while connected to the running power supply.

What I notice when it happen is that the current draw would be around .30 amp, twice the normal .15 amp that it draws when it's off.

Of course, a working solution would be to disconnect the radio from the power supply, or to turn the power supply off completely, which I do, but that's not why I'm posting this.

The thing is, I'd like to make sure that there's nothing wrong with my radio. I'd like to think it's the power supply's fault (or maybe the power line's), but I can't be sure.

Has anyone encountered something similar?

 

Hi everyone, is there a Yaesu rig user in the house?

I just got this beat up FT-2900R for cheap. It had a bunch of problems that I managed to fix, but one remains without a solution in sight.

For now, almost everything works normally, except for the fact it's showing considerably less voltage than the supply. During the start-up, it shows the voltage exactly as supplied only for a brief moment (long enough for me to read it) before droping around 3-4 volts. As the result, my transmit power gets cut-off due to the low voltage.

I even tried changing all the thru-hole caps, to no avail.

Not sure if this matters, but I'm powering it with a Meanwell style SMPS.

Anyone familiar with this issue?

 

You'll first need to have these in your SDDM config.

[General]
DisplayServer=wayland

I'd just have it in a new file called /etc/sddm.conf.d/wayland.conf

If you're used to configuring your login manager thru KDE's settings panel, you do not want to add to its config file as it will get overwritten everytime you save your settings.

Next would be your systemd. I personally think this solution is less than elegant, but it seems to be well supported, and more importantly, it works.

You'll need to go to the SDDM's systemd service file, located on /lib/systemd/system/sddm.service. Simply uncomment a line with

After=plymouth-stop.service

Best to test by rebooting.

Note:

Failure to do the systemd step would result in the sddm.service failing to run. When this happen, simply switch to a free tty and login. From here, you redo the systemd step. You can also restart the sddm.service (it will work).

view more: next ›