• Community

** libraries (KEY) Libraries are the most important building in any community in terms of long term value. When in doubt, always support libraries and fund them (regardless of your politics) and work to minimize laws that negatively impact libraries.

EVERY single community that burned library books or got rid of libraries are dead and it is better to be pissed about them having books you don't like than for you to lose your community and you to ultimately die because of it.

Besides books, some libraries also loan out tools and 3D printers; not to mention some provide free classes and shelter to those in need.

** Churches/Temples Make CERTAIN that everyone who is a member knows that in the event of disaster to go to church and bring supplies. This will enable a quick rebuild in the event of damage but also the preservation of as many lives as possible. Feed everyone (regardless of if they are church members or not) who shows up and protect everyone inside from the elements if possible.

If possible operate a soup kitchen for the homeless and have a library of tools on hand for repair. If the government was kind enough to build a fallout shelter for you, stocking a food pantry in there will supercharge community recovery.

Any church/temple that doesn't help the homeless/poor is going to be a deathtrap when disaster strikes (especially those mega-churches where the minister just enriches themselves).

A humble minister who lives in a small apartment/home and helps the homeless all week long is much more likely to have Jesus in his heart and do good than one who owns a private jet and a mansion in a different zip code.

** invincibility centers (done by governments) The centers are in essence a stopgap while utility crews scramble to fix cut power lines and put water mains back into operation, so basic services can be restored to hospitals and essentials prior to restoring services to homes and businesses.

Basically pick any building that the government owns, turn on the generators, let everyone in and give them beverages (coffee/tea/water), electricity and internet access. If done during winter or a heat wave, you'll save thousands (or more) lives.

** Soup kitchens I strongly recommend you set these up before any disaster occurs (or get coordinated with helping one now); because it will not be possible to convince people to give you all of that food AFTER a disaster if you are not actively feeding other people BEFORE a disaster and routinely asking for additional supplies.

It is generally easier to volunteer with one (to get coordinated) than to setup your own but if you need to setup your own, below are the steps.

Working in a soup kitchen will work against you in the event of an extreme famine as people will get paranoid about food hoarding.

*** Outline your basic plan You'll need to figure out these details first: the number of people you plan to serve daily food safety protocols the person in charge of the menu planning food service protocols for those with allergies and religious restrictions whether the food will be served in a cafeteria or restaurant style

*** Look for a Suitable Location Since you’re catering to the homeless, your ideal location should be near where your intended guests are. Remember that most homeless and underprivileged people don’t have cars. If your soup kitchen is far from where they are, it would be inaccessible for them.

If renting or buying your own place isn’t an option right now, you can also set up a soup kitchen in public places. Religious institutions like churches, mosques, synagogues, and temples are a great option too. They are usually accessible to the public and can hold large crowds. Don’t forget to ask for permission from these places first.

*** Register as a Non-Profit Registering your soup kitchen as a non-profit establishes its legal identity. It exempts you from paying tax and makes it easier to avail of government assistance programs for non-profits.

Each state has different procedures for registering charitable organizations. But it usually involves filing an Articles of Incorporation and applying for federal tax exemption. (which can take up to 2 years) To be sure, visit your state’s charity registration office.

*** Additional Paperwork After registering your soup kitchen as a non-profit, you’ll need to take care of additional paperwork like: insurance coverage for property and liability health insurance for your employees (if any) health and safety permits

*** Raise Funds and Food Donations As you know, soup kitchens run on donations. That’s why fundraising activities are essential in getting the soup kitchen up and running. There are plenty of ways to raise funds and donations for a soup kitchen. You can organize a food drive or fundraising activities like: crowdfunding charity auctions online donations selling customized shirts and merchandise charity walk/run charity raffle

*** Look for Volunteers Aside from donations, non-profits like soup kitchens also rely on volunteers to get things done. That’s why aside from raising funds, you also need to recruit volunteers.

Start with the people you know like friends and relatives. You can also involve people from your church, the local schools, or scout for volunteers online. There are plenty of places you can get volunteers from.

Plus, as I’ve said, it’s a great way of bringing people together to help the less fortunate. That’s why most soup kitchens don’t lack volunteers.

Allowing patrons to be volunteers has to be done carefully. You must be selective. It is not uncommon for patrons, who have been given even modest authority, to abuse it and start ordering people (other patrons, volunteers) around. While many patrons are sincere in their desire to help and are trying to give back, it is best to monitor the person until you are sure that they are helping for the right reasons.

*** Buy Necessary Food Service Equipment Obviously, you won’t be able to serve hot meals if you don’t have the proper food serving equipment.

During your planning stage, you already identified how many people you plan to serve per day and the kinds of food you’ll have on your menu. This should give you an idea of what kitchen equipment and tools to buy.

*** Stock Your Pantry This is one of the most important steps in running a soup kitchen. I mean, you can’t cook hot meals if you have nothing to cook, right?

Aside from the food donations, you can also reach out to food banks to see if they can help. Or if you have lots of restaurants and cafeterias in your area, try to see if they can donate some of their excess supplies. Working with local food pantries is where approximately 3/4 of ALL your food will be coming from. Sharing funds with the local pantries will enable bigger food orders and the dollars going much further.

*** Get the Word Out About Your Soup Kitchen Just like when opening a business, you also need to get the word out about your soup kitchen. You can announce it on social media or print posters and flyers. If you know people from the media, then much better.

"Marketing" your soup kitchen will not only help you reach the people you’re hoping to help. It can also connect you with the people who are interested in your cause.

** Food pantries I strongly recommend you set these up before any disaster occurs (or get coordinated with helping one now); because it will not be possible to convince people to give you all of that food AFTER a disaster if you are not actively feeding other people BEFORE a disaster and routinely asking for additional supplies.

It is generally easier to volunteer with one (to get coordinated) than to setup your own.

They tend to follow one of two organizational styles: Shopping Method: The client goes into the pantry; picks out what s/he needs, and fills his/her own bag/box. Ordering Method: The client receives a list of items available, or can view them from behind a table or counter; s/he will indicate which items s/he wants and how many. Staff/volunteers fill the boxes according to the order.

During disaster your first priority is getting supplies to the soup kitchens; so have good relationships with local soup kitchens (as they are the party which will be receiving your excess inventory). you'll be providing a food buffer to soup kitchens to keep people alive until supplies can be brought in from outside the disaster zone. Ideally you'll be well stocked but with current climate change and economic destruction of the working class; it isn't going to be pretty.

Ideally in good times, you'll just be a warehouse for storing food for soup kitchens but when things start to get tough (economically) you'll slowly switch to supplying basics to the working poor (and later to the working middle class) and after that you'll be tapped out and just be working hard trying to get additional supplies for the soup kitchens you partnered with.

Need = (number of people living at or below the poverty line) * 234 lbs. of food aid per year

Working in a food pantry will work against you in the event of an extreme famine as people will get paranoid about food hoarding.

And most food pantries are required to store records for 3 years about the people who received food, specifically: Name Address City, State, Zip Code Phone number Number in household Number of adults Number of children

This information is required by the IRS and is used by the government eligibility programs.

Multiple soup kitchens might pool funds with you to do bulk orders and if you can find a super shopper (someone who extreme coupons), you'll always be able raise funds to get additional supplies. As for every $1 of food a person could donate, $100 worth of food could be purchased by an effective food pantry.

Funding the creation of and growth of community gardens can build a good supply of perishable veg/fruits to supplement long term stored supplies.

CO2 scrubbing (slrpnk.net)
 

Each human exhales 42grams of CO2 per hour (1.1Kg per day).

*** Chemical reaction

**** Basic

A process commonly used to teach CO2 scrubbing to chemical engineering students involves sodium hydroxide (NaOH). The reaction is exothermic and is as follows: CO2 (g) + 2 NaOH (aq) → Na2CO3 (aq) + H2O (l)

The aqueous sodium carbonate is subsequently treated with calcium hydroxide (Ca(OH)2) to precipitate out calcium carbonate (CaCO3): Na2CO3 (aq) + Ca(OH)2 (aq) → 2 NaOH (aq) + CaCO3 (s)

Disclaimer:

This is usually done with much higher concentrations of CO2 (e.g. >10%) than you would find in the atmosphere (~400 ppm). The point of scrubbing in a chemical plant is to reduce emissions to a level that is still much higher than atmospheric CO2 levels but lower than governmental standards. I suspect that you would not see a noticeable change in ambient CO2 levels from putting something like this in a place with such (relatively) low CO2 to begin with. There is a very low driving force to push gaseous CO2 into the liquid and solvate it when the partial pressure of CO2 is low.

There exists a unique relationship between the partial pressure of CO2 above a solution, the dissolved carbon in the solution, and the pH of the solution.

So if you wanted to see what was going on in a controlled environment with no other species in the solution / that could enter the solution, you could just use a pH probe to see how much carbon was pushed into the solution.

Calcium hydroxide can be produced when quicklime (CaO) is mixed with water (H20). quicklime is usually made by the thermal decomposition of calcium carbonate (CaCO3). This is accomplished by heating the material to above 825C (1,517F) CaCO3 (s) → CaO (s) + CO2 (g)

The quicklime is not stable and, when cooled, will spontaneously react with CO2 from the air until, after enough time, it will be completely converted back to calcium carbonate unless slaked with water.

**** Apollo Spacecraft

***** Lithium hydroxide (outputs water)

2 LiOH + CO2 → Li2CO3 + H2O One gram of anhydrous lithium hydroxide can remove 450 cm^3 of carbon dioxide gas.

Lithium hydroxide is often produced industrially from lithium carbonate in a metathesis reaction with calcium hydroxide: Li2CO3 + Ca(OH)2 → 2 LiOH + CaCO3 The initially produced hydrate is dehydrated by heating under vacuum up to 180C.

You will need 1.1Kg per person per day. If you are not going into space, buy calcium hydroxide, it is much cheaper ($125 per ton vs $30 per kilogram)

***** Lithium peroxide (outputs oxygen)

It is prepared by the reaction of hydrogen peroxide and lithium hydroxide. This reaction initially produces lithium hydroperoxide: LiOH + H2O2 → LiOOH + H2O

This lithium hydroperoxide may exist as lithium peroxide monoperoxohydrate trihydrate (Li2O2·H2O2·3H2O). Dehydration of this material gives the anhydrous peroxide salt: 2 LiOOH → Li2O2 + H2O2

Li2O2 decomposes at about 450C to give lithium oxide: 2 Li2O2 → 2 Li2O + O2

And absorbs CO2 in the following: Li2O2 + CO2 → Li2CO3 + 1⁄2 O2

Similar to the reaction of lithium hydroxide with carbon dioxide to release 1 Li2CO3 and 1 H2O, lithium peroxide has high absorption capacity and absorbs more CO2 than does the same weight of lithium hydroxide and offers the bonus of releasing oxygen instead of water.

**** Amine gas treating

The primary application for CO2 scrubbing is for the enclosed atmosphere of nuclear submarines. The technology being involves the use of various amines, e.g. monoethanolamine. Cold solutions of these organic compounds bind CO2, but the binding is reversed at higher temperatures: CO2 + 2 HOCH2CH2NH2 ↔ HOCH2CH2NH+3 + HOCH2CH2NHCO−2

The above reaction has been utilized as a primary part of atmosphere control in nuclear submarines since the late 1950s.

The amine concentration in the absorbent aqueous solution is an important parameter in the design and operation of an amine gas treating process. Depending on which one of the following four amines the unit was designed to use and what gases it was designed to remove, these are some typical amine concentrations, expressed as weight percent of pure amine in the aqueous solution: Monoethanolamine(MEA): About 20% for removing H2S and CO2, and about 32% for removing only CO2. Diethanolamine (DEA): About 20 to 25% removing H2S and CO2 Methyldiethanolamine (MDEA): About 30 to 55% for removing H2S and CO2 Diglycolamine: About 50 % for removing H2S and CO2

Additionally you could use: Diisopropanolamine (DIPA) Aminoethoxyethanol (Diglycolamine) (DGA)

Both H2S and CO2 are acid gases and hence corrosive to carbon steel. However, in an amine treating unit, CO2 is the stronger acid of the two. H2S forms a film of iron sulfide on the surface of the steel that acts to protect the steel. When treating gases with a high percentage of CO2, corrosion inhibitors are often used and that permits the use of higher concentrations of amine in the circulating solution.

MEA and DEA are primary and secondary amines. They are very reactive and can effectively remove a high volume of gas due to a high reaction rate. However, due to stoichiometry, the loading capacity is limited to 0.5 mol CO2 per mole of amine. MEA and DEA also require a large amount of energy to strip the CO2 during regeneration, which can be up to 70% of total operating costs. They are also more corrosive and chemically unstable compared to other amines.

Piperazines have been proposed for carbon capture and storage (CCS) because piperazine protects other amines from degradation. Piperazine can be thermally regenerated through multi-stage flash distillation and other methods after being used in operating temperatures up to 150C and recycled back into the absorption process, providing for higher overall energy performance in amine gas treating processes.

Typical absorption column operating range: 35-50C and 5-205 atm of absolute pressure.

*** Fractional Distillation of Liquid Air

Effectively you need only have a good phase diagram for the gases and control the temperature, pressure or both. But lacking those phase diagrams, the following list of triple points should be sufficient to build an approximate working distillation:

(The below looks best in fix width font in a textfile)

| Substance | Temperature (C) | Pressure (kPa) | % of Air | |----------------------+-----------------+----------------+------------| | Air | -213.40 | 5.265 | 100% | | Nitrogen | -209.97 | 12.6 | 78.084% | | Oxygen | -218.79 | 0.152 | 20.9476% | | Water | 0.01 | 0.611657 | 5% - 0.25% | | Argon | -189.34 | 68.9 | 0.934% | | Carbon dioxide | -56.60 | 517 | 0.04% | | Neon | -248.58 | 43.2 | 0.001818% | | Methane | -182.47 | 11.7 | 0.0002% | | Helium | -271.378 | 30.016 | 0.000524% | | Krypton | -157.39 | 74.12 | 0.000114% | | Hydrogen | -259.31 | 7.04 | 0.00005% | | Xenon | -111.8 | 81.5 | 0.0000087% | | Ozone | -192.55 | 0.00114 | 0.000007% | | Nitrogen Dioxide [0] | -11.25 | 18.728 | 0.000002% | | Iodine | 113.50 | 12.07 | 0.000001% | | Acetylene | -80.7 | 120 | Trace | | Ammonia | -77.75 | 6.076 | Trace | | Arsenic | 820 | 3628 | Trace | | Butane | -138.6 | 0.0007 | Trace | | Carbon (graphite) | 4492 | 10132 | Trace | | Carbon monoxide | -205.05 | 15.37 | Trace | | Chloroform | -97.72 | 0.870 | Trace | | Deuterium | -254.52 | 17.1 | Trace | | Ethane | -183.26 | 0.0008 | Trace | | Ethanol | -123 | 0.00000043 | Trace | | Ethylene | -169.2 | 0.12 | Trace | | Formic acid | 8.25 | 2.2 | Trace | | Hexafluoroethane | -100.07 | 26.60 | Trace | | Hydrogen chloride | -114.19 | 13.9 | Trace | | Isobutane | -159.60 | 0.000019481 | Trace | | Mercury | -39.0 | 0.000000165 | Trace | | Nitric oxide | -163.65 | 21.92 | Trace | | Nitrous oxide | -90.81 | 87.85 | Trace | | Palladium | 1552 | 0.0035 | Trace | | Platinum | 1772 | 0.00020 | Trace | | Radon | -71 | 70 | Trace | | Sulfur dioxide | -75.46 | 1.67 | Trace | | Titanium | 1668 | 0.0053 | Trace | | Uranium hexafluoride | 64.02 | 151.7 | Trace |

[0] numbers are a bit questionable

If you have a random sample of gases, you can separate them by gradually cooling the sample until each component gas liquifies. The liquified compound falls to the bottom of a collection vessel. After all of the liquid has been retrieved, cooling continues until the temperature drops to the boiling point of the next compound and it liquifies. Some compounds, such as carbon dioxide, never liquify. Instead, they turn directly into solids, which are easier to retrieve than liquids. (CO2 turns into a liquid over 516.7575kPa between 31.1C and -56.6C)

Put your sample in a vessel that is slightly warmer at the bottom (-185C) than it is at the top (-190C). Oxygen liquifies at -183C, so it flows out of the flask through a tube in the bottom. Nitrogen turns back into a gas, however, because its boiling point is -196C. It flows out through a tube connected to the top of the flask. Repeat to isolate all other gases.

If you only want to isolate CO2, compress it to between 5.11atm (516.7575kPa) and 72.79atm (7375.447kPa) and cool to -57C or at standard atomospheric pressure cool t0 -78C, CO2 gas will directly convert to solid (dry ice) You can do 750 kg/hr at 11Kw or 80 kg/hr at 3Kw

 

This is an odd bit of political trivia but enough of the states which Trump won his electoral votes from have laws forbidding Felons from taking office. If the democratic party just sues in those state, they could revoke enough electoral votes to prevent Trump from getting his second term.

It just requires them to enforce the laws that already exist. The only counter the Republicans have is to repeal the laws preventing felons from holding office. (Some of them started to realize this https://www.latintimes.com/republican-bill-inspired-trump-would-let-convicted-felons-run-public-office-missouri-568981)

 
  • Ammonia (NH3)

Very popular scrubbing solvent to remove pollutants from fossil fuel combustion streams before they can be released to the atmosphere. Also a popular refrigerant and precursor to nitric acid. (Key to making artificial fertilizers)

  • Calcium Oxide (CaO) [quicklime or burnt lime]

As a cheap and widely available alkali. About 50% of the total quicklime production is converted to calcium hydroxide before use. Both quick- and hydrated lime are used in the treatment of drinking water.

It can be created by heating the limestone to 900°C for several hours which would turn the limestone into quick lime

  • Calcium hydroxide [hydrated lime, caustic lime, builders' lime, slack lime, cal or pickling lime]

Calcium hydroxide is commonly used to prepare lime mortar.

One significant application of calcium hydroxide is as a flocculant, in water and sewage treatment. It forms a fluffy charged solid that aids in the removal of smaller particles from water, resulting in a clearer product. This application is enabled by the low cost and low toxicity of calcium hydroxide. It is also used in fresh-water treatment for raising the pH of the water so that pipes will not corrode where the base water is acidic, because it is self-regulating and does not raise the pH too much.

It can be created by combining quicklime with water to form slaked lime

  • Ethylene (C2H4)

Probably the most popular industrial precursor to polymer manufacturing

  • Hydrochloric Acid (HCl)

Used mainly in the production of other chemicals (by acting as a reactant or a catalyst)

  • Methanol (CH3OH)

Used as a reactant to make methyl tertbutyl ether (MTBE), formaldeyde, and acetic acid.

  • Nitric Acid (HNO3)

Most common application is its reaction with ammonia to form the solid fertilizer ammonium nitrate the most widely used solid fertilizer. Nitric acid is subject to thermal or light decomposition and for this reason it was often stored in brown glass bottles Nitric acid's boiling point of 83 °C. (68% solution boils at 121 °C).

Dilute nitric acid may be concentrated by distillation up to 68% acid, which is a maximum boiling azeotrope. In the laboratory, further concentration involves distillation with either sulfuric acid or magnesium nitrate, which serve as dehydrating agents. Such distillations must be done with all-glass apparatus at reduced pressure, to prevent decomposition of the acid. Industrially, highly concentrated nitric acid is produced by dissolving additional nitrogen dioxide in 68% nitric acid in an absorption tower.

The dissolved NOx is readily removed using reduced pressure at room temperature (10-30 minutes at 200 mmHg or 27 kPa) to give white fuming nitric acid.

  • Propylene (C3H6)

Another industrial polymer precursor

  • Sodium Carbonate (Na2CO3) [washing soda, soda ash and soda crystals]

Used in many cleaning agents and in glass making. Sodium oxide is a component of most glass, although it is added in the form of "soda" (sodium carbonate). Typically, manufactured glass contains around 15% sodium oxide, 70% silica (silicon dioxide) and 9% lime (calcium oxide). The sodium carbonate "soda" serves as a flux to lower the temperature at which the silica mixture melts. Soda glass has a much lower melting temperature than pure silica, and has slightly higher elasticity.

  • Sodium hypochlorite (NaClO) [liquid bleach]

A method of producing sodium hypochlorite involving the electrolysis of brine to produce sodium hydroxide and chlorine gas, which then mixed to form sodium hypochlorite.

Today, an improved version of this method, known as the Hooker process (named after Hooker Chemicals, acquired by Occidental Petroleum), is the only large-scale industrial method of sodium hypochlorite production. In the process, sodium hypochlorite (NaClO) and sodium chloride (NaCl) are formed when chlorine is passed into cold dilute sodium hydroxide solution. The chlorine is prepared industrially by electrolysis with minimal separation between the anode and the cathode. The solution must be kept below 40 °C (by cooling coils) to prevent the undesired formation of sodium chlorate.

Sodium hypochlorite can be easily produced for research purposes by reacting ozone with salt. NaCl + O3 → NaClO + O2 This reaction happens at room temperature and can be helpful for oxidizing alcohols.

  • Sodium Hydroxide (NaOH) [lye and caustic soda]

The most popular alkaline substance in industry. Widely used in dyes and soap manufacturing. Also a good cleaning agent and can be used to neutralize acids.

  • Sulfuric Acid (H2SO4)

Probably the most common industrial acid. Used widely in mineral leaching and gas scrubbing (removing dangerous substances). Also used to neutralize alkaline substances and as an electrolyte in lead-acid batteries. A nation's sulfuric acid production is a good indicator of its industrial strength. Sulfuric acid can be obtained by dissolving sulfur trioxide in water.

  • potassium carbonate (K2CO3) [Potash]

Used in agriculture as a crop fertilizer.

  • Urea (CO(NH2)2) [carbamide]

More than 90% of world industrial production of urea is destined for use as a nitrogen-release fertilizer.Urea has the highest nitrogen content of all solid nitrogenous fertilizers in common use. Therefore, it has a low transportation cost per unit of nitrogen nutrient.

An essential ingredient in diesel exhaust fluid (DEF), which is 32.5% urea and 67.5% de-ionized water. DEF is sprayed into the exhaust stream of diesel vehicles to break down dangerous NOx emissions into harmless nitrogen and water.

The most common impurity of synthetic urea is biuret (HN(CONH2)2), which impairs plant growth.

  • Lithium peroxide

It is prepared by the reaction of hydrogen peroxide and lithium hydroxide. This reaction initially produces lithium hydroperoxide: LiOH + H2O2 → LiOOH + 2 H2O

This lithium hydroperoxide has also been described as lithium peroxide monoperoxohydrate trihydrate (Li2O2·H2O2·3H2O). Dehydration of this material gives the anhydrous peroxide salt: 2 LiOOH → Li2O2 + H2O2 + 2 H2O

Li2O2 decomposes at about 450 °C to give lithium oxide: 2 Li2O2 → 2 Li2O + O2

It is used in air purifiers where weight is important, e.g., spacecraft to absorb carbon dioxide and release oxygen in the reaction.

 
  • Haber-Bosch process

the Haber-Bosch process, is an artificial nitrogen fixation process and is the main industrial procedure for the production of ammonia today. The process converts atmospheric nitrogen (N2) to ammonia (NH3) by a reaction with hydrogen (H2) using a metal catalyst under high temperatures and pressures. This conversion is typically conducted at pressures above 10 MPa (100 bar; 1,450 psi) and between 400 and 500 °C (752 and 932 °F), as the gases (nitrogen and hydrogen) are passed over four beds of catalyst, with cooling between each pass for maintaining a reasonable equilibrium constant. On each pass only about 15% conversion occurs, but any unreacted gases are recycled, and eventually an overall conversion of 97% is achieved.

  • Ostwald process

Ammonia is converted to nitric acid in 2 stages. Typical conditions for the first stage, which contribute to an overall yield of about 98%, are: pressure is between 4-10 standard atmospheres (410-1,000 kPa; 59-150 psi) and temperature is about 870-1,073 K (600-800 °C; 1,100-1,500 °F).

Stage 1

It is oxidized by heating with oxygen in the presence of a catalyst such as platinum with 10% rhodium, platinum metal on fused silica wool, copper or nickel, to form nitric oxide (nitrogen(II) oxide) and water (as steam). This reaction is strongly exothermic, making it a useful heat source once initiated.

Stage 2

Stage two encompasses two reactions and is carried out in an absorption apparatus containing water. Initially nitric oxide is oxidized again to yield nitrogen dioxide (nitrogen(IV) oxide). This gas is then readily absorbed by the water, yielding the desired product (nitric acid, albeit in a dilute form), while reducing a portion of it back to nitric oxide. The NO is recycled, and the acid is concentrated to the required strength by distillation.

  • Contact process

The contact process is the current method of producing sulfuric acid in the high concentrations needed for industrial processes. In addition to being a far more economical process for producing concentrated sulfuric acid than the previous lead chamber process, the contact process also produces sulfur trioxide and oleum.

The process can be divided into six stages: Combining of sulfur and oxygen (O2) to form sulfur dioxide Purifying the sulfur dioxide in a purification unit Adding an excess of oxygen to sulfur dioxide in the presence of the catalyst vanadium pentoxide at 450 °C and 1-2 atm The sulfur trioxide formed is added to sulfuric acid which gives rise to oleum (disulfuric acid) The oleum is then added to water to form sulfuric acid which is very concentrated. As this process is an exothermic reaction so the temperature should be as low as possible.

  • Solvay process

The Solvay process or ammonia-soda process is the major industrial process for the production of sodium carbonate (soda ash, Na2CO3). The ingredients for this are readily available and inexpensive: salt brine (from inland sources or from the sea) and limestone (from quarries).

In industrial practice, the reaction is carried out by passing concentrated brine (salt water) through two towers. In the first, ammonia bubbles up through the brine and is absorbed by it. In the second, carbon dioxide bubbles up through the ammoniated brine, and sodium bicarbonate (baking soda) precipitates out of the solution.

The necessary ammonia "catalyst" for reaction (I) is reclaimed in a later step, and relatively little ammonia is consumed. The carbon dioxide required for reaction (I) is produced by heating ("calcination") of the limestone at 950-1100 °C, and by calcination of the sodium bicarbonate. The calcium carbonate (CaCO3) in the limestone is partially converted to quicklime (calcium oxide (CaO)) and carbon dioxide.

The sodium bicarbonate (NaHCO3) that precipitates out in reaction (I) is filtered out from the hot ammonium chloride (NH4Cl) solution, and the solution is then reacted with the quicklime (calcium oxide (CaO)) left over from heating the limestone in step (II).

CaO makes a strong basic solution. The ammonia from reaction (III) is recycled back to the initial brine solution of reaction (I).

The sodium bicarbonate (NaHCO3) precipitate from reaction (I) is then converted to the final product, sodium carbonate (washing soda: Na2CO3), by calcination (160-230 °C), producing water and carbon dioxide as byproducts.

The carbon dioxide from step (IV) is recovered for re-use in step (I). When properly designed and operated, a Solvay plant can reclaim almost all its ammonia, and consumes only small amounts of additional ammonia to make up for losses. The only major inputs to the Solvay process are salt, limestone and thermal energy, and its only major byproduct is calcium chloride, which is sometimes sold as road salt.

In the modified Solvay process developed by Chinese chemist Hou Debang in 1930s, the first few steps are the same as the Solvay process. However, the CaCl2 is supplanted by ammonium chloride (NH4Cl). Instead of treating the remaining solution with lime, carbon dioxide and ammonia are pumped into the solution, then sodium chloride is added until the solution saturates at 40 °C. Next, the solution is cooled to 10 °C. Ammonium chloride precipitates and is removed by filtration, and the solution is recycled to produce more sodium carbonate. Hou's process eliminates the production of calcium chloride. The byproduct ammonium chloride can be refined, used as a fertilizer and may have greater commercial value than CaCl2, thus reducing the extent of waste beds.

  • Chloralkali process

The most common chloralkali process involves the electrolysis of aqueous sodium chloride (a brine) in a membrane cell. A membrane, such as one made from Nafion (sulfonated tetrafluoroethylene based fluoropolymer-copolymer), is used to prevent the reaction between the chlorine and hydroxide ions. (asbestos can perform this function less efficiently)

Saturated brine is passed into the first chamber of the cell where the chloride ions are oxidised at the anode, losing electrons to become chlorine gas: 2Cl- → Cl2 + 2e-

At the cathode, positive hydrogen ions pulled from water molecules are reduced by the electrons provided by the electrolytic current, to hydrogen gas, releasing hydroxide ions into the solution: 2H2O + 2e- → H2 + 2OH-

The ion-permeable ion-exchange membrane at the center of the cell allows the sodium ions (Na+) to pass to the second chamber where they react with the hydroxide ions to produce caustic soda (NaOH). The overall reaction for the electrolysis of brine is thus: 2NaCl + 2H2O → Cl2 + H2 + 2NaOH

The process has a high energy consumption, for example around 2500 kWh of electricity per tonne of sodium hydroxide produced. Because the process yields equivalent amounts of chlorine and sodium hydroxide (two moles of sodium hydroxide per mole of chlorine), it is necessary to find a use for these products in the same proportion. For every mole of chlorine produced, one mole of hydrogen is produced. Much of this hydrogen is used to produce hydrochloric acid The method is analogous when using calcium chloride or potassium chloride, producing calcium hydroxide or potassium hydroxide.

  • Water-gas shift reaction

With the development of industrial processes that required hydrogen, such as the Haber-Bosch ammonia synthesis, a less expensive and more efficient method of hydrogen production was needed.

So starting with coal and performing coal gasification: 3C (i.e., coal) + O2 + H2O → H2 + 3CO

Then using 3CO to perform the water-gas shift reaction: CO + H2O ⇌ H2 + CO2

Low temperature shift catalysis

Catalysts for the lower temperature WGS reaction are commonly based on copper or copper oxide loaded ceramic phases, While the most common supports include Alumina or alumina with zinc oxide, other supports may include rare earth oxides, spinels or perovskites. A typical composition of a commercial LTS catalyst has been reported as 32-33% CuO, 34-53% ZnO, 15-33% Al2O3. The active catalytic species is CuO. The function of ZnO is to provide structural support as well as prevent the poisoning of copper by sulfur. The Al2O3 prevents dispersion and pellet shrinkage. The LTS shift reactor operates at a range of 200-250 °C. The upper temperature limit is due to the susceptibility of copper to thermal sintering. These lower temperatures also reduce the occurrence of side reactions that are observed in the case of the HTS.

High temperature shift catalysis

The typical composition of commercial HTS catalyst has been reported as 74.2% Fe2O3, 10.0% Cr2O3, 0.2% MgO (remaining percentage attributed to volatile components). The chromium acts to stabilize the iron oxide and prevents sintering. The operation of HTS catalysts occurs within the temperature range of 310 °C to 450 °C. The temperature increases along the length of the reactor due to the exothermic nature of the reaction. As such, the inlet temperature is maintained at 350 °C to prevent the exit temperature from exceeding 550 °C. Industrial reactors operate at a range from atmospheric pressure to 8375 kPa (82.7 atm). The search for high performance HT WGS catalysts remains an intensive topic of research in fields of chemistry and materials science. Activation energy is a key criteria for the assessment of catalytic performance in WGS reactions. To date, some of the lowest activation energy values have been found for catalysts consisting of copper nanoparticles on ceria support materials, with values as low as Ea = 34 kJ/mol reported relative to hydrogen generation.

view more: next ›