sorted by: new top controversial old
IPv4 is hard in c/linuxmemes@lemmy.world
Valve "played capitalism so well they broke it" and now Steam can never be replaced, former Epic dev says: "I don't think this is fixable" in c/pcgaming@lemmy.ca
Anon thinks she's exaggerating in c/greentext@sh.itjust.works
Anon plays an RPG in c/greentext@sh.itjust.works
Jury unanimously acquits Churchill statue spray-painter in c/unitedkingdom@feddit.uk
It only counts when I say it does in c/politicalmemes@lemmy.world
[–] 6 points 2 months ago (2 children)

I think some of that stems from Zelensky holding Israel in favor a lot. He's had multiple positive comments about it, even though Israel is doing what Russia did to Ukraine (or tried to do really)

  • permalink
  • fedilink
  • source
  • parent
  • context
    • just realized whoogle is dead now in c/selfhosted@lemmy.world
    [–] 1 point 3 months ago

    I like lens feature a lot. I also use their privacy pass feature quite a bit. Overall there are a lot of really nice features and search results as good or better than Google. DDG uses bing which is junk IMO

  • permalink
  • fedilink
  • source
  • parent
  • context
    • just realized whoogle is dead now in c/selfhosted@lemmy.world
    Game suggestions: Downvote any game you've heard of before in c/games@lemmy.world
    How would you expose Jellyfin securely without a vpn? in c/selfhosted@lemmy.world
    [–] 8 points 5 months ago

    You can do a reverse proxy + authelia (or other auth service). It's still more risky than a VPN IMO, buts wayyyy better than some of the other options in this thread

  • permalink
  • fedilink
  • source
    •
    Is anyone paying for Kagi, the search engine? What is your experience with it? in c/privacy@lemmy.dbzer0.com
    People who are staying on Plex, have you tried Jellyfin? What about it do you not prefer? (real question) in c/selfhosted@lemmy.world
    73
    If you selfhost audiobooks, check out ReadMeABook (github.com)
     

    Just a PSA. I didn't see any posts on here about it, but have really been enjoying it and the wife likes it a lot. It solved a lot of manual effort on my part for getting audiobooks into Audiobookshelf w/o much manual intervention. The request system is similar to *seerr and its pretty simple to setup. Bonus: it supports OIDC out of the box, which I appreciate so I dont have one more account to manage.

    41
    Odd wiring in a 2-gang (lemmy.world)
     

    I am installing smart switches in my home. I have this 2-gang box at the top of our stairs, where I am doing a virtual 3-way setup for both switches. One powers the light on the stairs, the other the hallway at the top of the stairs. A few things:

    • This box has no live wires since its the other side of the two 3-ways (I have tested this by disconnecting all wires from all switches and checking for lives).
    • Each of the boxes is on a separate breaker. It has TWO sets of neutral pigtails in the back. This is the correct setup, but its possible the neutrals where mixed up during the original wiring of the house.
    • Each set of romex wires is connected to another set of romex. None of them criss-cross (except the grounds).

    Now, here is my odd behavior and my need for assistance:

    After wiring the two virtual 3-way setups (Option 2 from this page) everything was working fine. I was also planning to switch out the fixtures, so I went back and turned off the breaker for the hallway, but the smart switch for the hallway was still active (LED is on, I can see it on homeassistant). Now, I am thinking the original wiring mixed up the loads in the box with the incoming wires and the two neutrals for those breakers have been connected...anyone have thoughts on whats going on? is the solution here to basically swap the incoming 3-wire load romex?

    **Solution: ** I am not 100% certain the cause of the issue. It is possible I mixed the wiring up when doing the virtual 3-way, but I basically followed the advice here and started from scratch. I traced the travelers from each of the main boxes and connected them to the appropriate load and completed disconnected the 3-way part. once I had the right load on the right travelers, I then setup the virtual switches wiring off the black wire coming with the traveler. Lastly, I ensured the neutrals from the two romexs that had a traveler+load where pigtailed with the virtual switch. took a bit of time, but felt this was the easiest way to not spin my wheels too much. Appreciate the advice, if anyone really does want, I can put together a diagram (on paper 😉 )

    view more: next ›