[–] 1 point 5 months ago (1 child)

I had an idea it's configurable in its admin-panel, but it may not. Please check the following:

So, to conclude: the official documentation is right. Hot-swappable or not, the UPS cannot boot without at least a bit of charge in the batteries. That's all it requires to come back online — and start to fully charge the batteries. I did not experiment to see if, after having booted, I could remove the batteries at will and put them back in again, with the UPS automatically managing the switch to AC power. So that question remains unanswered.

The problem, in your case (as well as on mine) is that the batteries have to be installed first before you know if the motherboard is fine or not.

Source

  • source
  • [–] [S] 1 point 5 months ago

    My other ups which is an APC will work and pass power even with out a battery. And it's not hot swappable. It will just beep.

    This UPS doesn't even do anything, it doesn't even beep. The cables going to the battery don't seem to be pushing any voltage according to my multimeter when I complete the circuit. And it doesn't help the tripplite isn't consumer friendly when it comes to self service.

  • source
  • parent
  • context
  • [–] 3 points 5 months ago* (2 children)

    Super confused about the situation here. You bought a UPS without batteries? I would assume the side marked for batteries+surge would not operate properly if no batteries were present if this model isn't hot-swappable.

    Edit: the product page says this unit should be hot-swappable, BUT, it may require the batteriesnto be present first in order to engage the PDU to turn on power to each individual outlet, so mayyyybe getting batteries would make it work, but who knows.

  • source
  • [–] [S] 2 points 5 months ago

    The problem with finding where and how to make adjustments is I can't work out the physics/engineering of what is causing it, or what the original design was meant to be like. But the other comment does sound useful in this way

  • source
  • parent
  • context
  • [–] 3 points 5 months ago* (last edited 5 months ago) (2 children)

    Alternatively put a small insulator on top of the fan case so it keeps the laptop case away from the fan itself.

    It may have come with this and it broke down over time.

    I've used Goop adhesive like this on a very old Dell Lenovo X series. Ran a bead on top of the main fan body because it would vibrate against the plastic part of the case, but only when my wrist was on the keyboard.

    Nice thing about Goop is it remains rubbery, and you can smooth it down while it's still wet to make it as thin as needed (just lick your finger and it won't stick to you).

    Goop is freakin' magic glue. I've glued laptops back together with it, yet it's removeable too.

  • source
  • parent
  • context
  • [–] 2 points 5 months ago* (1 child)

    Glad to hear it. Just out of curiosity, and for anyone who might run across this in the future trying to accomplish something similar, is your copy of Termux running rooted? I wouldn't have thought that it'd be possible without root privilege. You did mention Magisk above.

  • source
  • parent
  • context
  • [–] 5 points 5 months ago (4 children)

    Sounds like the case itself may be warped.

    It's going to be hard to fix. You may be able to sand down the area around the fan. Be sure to use fine grit paper, go slowly, and clean off any loose plastic bits afterward.

    I'm guessing you already verified that everything's aligned properly and attached snugly.

  • source
  • [–] 3 points 5 months ago (1 child)
    1. Go into your BIOS and make sure the SATA controller is enabled. Many modern boards have it disabled by default since most machines use M.2 slots for SSDs.

    2. If your on-board USB ports work fine, but your extension ports on the front of machine do not, it's most likely a voltage issue. Double check the USB pinouts on your new board with the extender it's connected to.

  • source
  • [–] 2 points 6 months ago

    hm, 3A should be enough for the Pi4... barely. it's theoretical maximum draw is 15.3W, so if you're maxing it out a lot you could be seeing brownouts. doesn't sound like you are though.

    also, if you think metal fatigue is wild, wait till you hear about tin whiskers.

  • source
  • parent
  • context
  • [–] [S] 2 points 6 months ago* (last edited 6 months ago) (1 child)

    EDIT: Pasted wrong link to power supply. Corrected!

    Never thought I'd hear "coil whine" in any other context than GPUs. 😅 Also, "metal fatigue" was a new concept to me, which anthropomorphizes the Pi to such an extent that I feel bad for it. But I'm hypersensitive.

    I am running one USB-A to Ethernet dongle off of one of the USB 3 ports, nothing else. I just checked the LEDs on the dongle, the Pi's Ethernet port and on my switch that ties a lot of other stuff together before it all goes to my ISP's fiber box (forgot the official name), and they are flashing with that rhythm that usually indicate Gbps speeds.

    The power supply is a 5V one: https://us.rs-online.com/product/okdo/2012167/72127392/

    Tomorrow, I'll actually open up the chassi to check the board for defects.

    Thank you very much for your reply! 🙂

  • source
  • parent
  • context
  • [–] 4 points 6 months ago (2 children)

    sounds like coil whine to me. if it started out of nowhere, it could be because of metal fatigue. if the leds are out, could be a cracked solder joint.

    i'm seeing warnings about the pcie regulator, how much are you running off the usb ports? also what is your power supply rated for?

  • source
  • view more: ‹ prev next ›